Ikos Pegasus reverse engineering

From Tmplab

Overview

What?

A big FPGA based ASIC emulator from the late 90s. Hundreds of FPGAs, thousands of I/Os, hundreds of amperes, dozens of kilos, etc. The FPGAs are quite old (approx. 1/3 the size and 1/3 the speed of a Virtex4 XC4VLX25) but there are many of them, brute forcing designs can be usually deeply pipelined to make river cruises in france Spotsylvania reckless driving them fast even on slow FPGAs, and it is a great restaurant supplies learning tool.

  • The rack with the power supply can hold up to 7 boards connected via a backplane.
  • One main board with:
    • SCSI controller
    • 8051
    • CPLD
    • FPGAs
    • SDRAM
  • 5 auxiliary boards with (each):
    • 1 XC95216 CPLD
    • 64 XC4036XL FPGAs
    • lots of SRAM
  • One auxiliary board was destructively reverse engineered, so only 4 are remaining.

Some device photos are here.

See also business articles about the product and its manufacturer:

There are also some reports of using the device in academia, many papers are available from the I€€€ if you have some grease money to spare.

Some hints about the original software here: http://groups.csail.mit.edu/cag/raw/benchmark/include/vmw/interface/slic/driver/

Who?

Lekernel and Aeris are doing the reverse engineering, Yann provided the device and Alex helped carrying it into the lab. Other contributors are welcome.

Programming the auxiliary boards

Situation

In normal operation, the CPLD receives configuration data from the backplane (originating from the mainboard through the SCSI port) and distributes it to the FPGAs. The CPLD uses JTAG to send data to the FPGAs. The 64 FPGAs on each auxiliary board are arranged to form one big JTAG chain driven by the CPLD.

Because this mode of operation uses a proprietary protocol which is especially hard to reverse engineer since we do not have the original software and SCSI device driver, we are trying to program the local search engine optimization boards with a JTAG probe.

FPGA JTAG pins

Here is the pinout of the JTAG port on the FPGAs (in BGA packages), as published by Xilinx.

Signal Pin
TMS K30
TCK D31
TDI D30
TDO C4

CPLD access

The CPLD's JTAG port is accessible on each board with a HE10 connector following the MultiLINX pinout.

Vref GND NC NC NC NC NC NC NC
NC TDO NC X TDI TCK TMS NC NC

Legend: X = missing pin (key), NC = No Connect

We can use urJTAG to access the CPLD, with the BSDL files released by Xilinx to enable boundary scan. For an unknown reason, the Xilinx iMPACT tool fails to recognize the Audrey Hepburn quotes CPLD.

How to use boundary scan with urJTAG

For Xilinx cable :

 cable xpc_ext

For FTDI cable :

 cable USB-to-JTAG-IF
 bsdl path [path to BSDL files]
 detect
 instruction EXTEST
 shift ir
 set signal [pin name from BSDL] out 1
 shift dr

FPGA JTAG chain topology

All the 64 FPGAs are arranged in a daisy chain for TDI and TDO.

For TCK and TMS, the board is divided into 4 quadrants and these signals are shared within each quadrant.

Ikos jtag.png

Connection of the FPGA JTAG chain to the CPLD

TCK and TMS are not directly connected to the CPLD, but go through a column of 74xx244 TTL buffers in the middle of the board. TDI and TDO are directly connected to the CPLD.

Signal Quadrant CPLD pin
TDI All 96
TDO All 92
TCK Q1 88
TCK Q2 TBD
TCK Q3 TBD
TCK Q4 90
TMS Q1 115
TMS Q2 TBD
TMS Q3 TBD
TMS Q4 TBD

Pins can be found by soldering LEDs on the FPGA pins and then using dichotomy to isolate each signal on the CPLD. Here are the urJTAG commands to set all pins to 1 on the CPLD. This should light up all the LEDs you soldered. Set all pins to 0 using similar commands to turn off the LEDs. Then, set only half of the pins to 1, look at the LEDs and this will tell you in which half of the CPLD pins the signal you're looking for is. Repeat the technique until a single pin is found.

Fortunately, the Pegasus does not bomb when you mess up with the CPLD, at least when only one board is inserted with all its FPGAs desoldered.

LEDs

Each auxiliary board has 2 LEDs in the front. They are connected to CPLD pins 58 and 86 in current sink (active low) mode. They can be useful to test your CPLD boundary scan setup.

Design tools

Synthesis

You will need to use Synplify which supports the XC4000 family of FPGAs. There is no Xst support whatsoever.

Place and route

Synplify generates an EDIF netlist which can be fed to the ISE Classics tools for place and route and bitstream generation.

FPGA JTAG programming

TODO

  • JTAG tunnelling through the CPLD boundary scan?
  • or reprogram the CPLD to re-route JTAG somewhere else?
  • does iMPACT support XC4000s?
  • it seems urJTAG has some FPGA programming support.

Interconnect

Once we have full JTAG access to the FPGAs, the reverse engineering of the interconnect can be vastly automated by using techniques such as that of NSA@home.

FPGA to FPGA

TBD

FPGA to SRAM

TBD

FPGA to I/O port

TBD

Board to board

TBD